Exam 1 of 3 | Exam 2 of 3 | Exam 3 of 3

CCNA2 v4.0 Final Exam – 2012

Exam 1 of 3 | Exam 2 of 3 | Exam 3 of 3

CCNA3 v4.0 Final Exam – 2012

Coming soon

1. Refer to the routing table shown in the exhibit. What is the meaning of the highlighted value 192?

It is the value assigned by the Dijkstra algorithm that designates the number of hops in the network.
It is the value used by the DUAL algorithm to determine the bandwidth for the link.
It is the metric, which is cost.
It is the administrative distance.

2. What is the purpose of the TTL field within an IP packet header?

clears an unreachable route from the routing table after the invalid timer expires
prevents regular update messages from inappropriately reinstating a route that may have gone bad
removes an unreachable route from the routing table after the flush timer expires
limits the period of time or number of hops a packet can traverse through the network before it should be discarded
used to mark the route as unreachable in a routing update that is sent to other routers

3. When would the network administrator use the ip bandwidth-percent eigrp as-number percent command?

when there is a low bandwidth connection
when the connection is on a shared medium
when the connection is serial instead of Ethernet
when the link is always busy

4. What is the function of the OSPF LSU packet?

used to confirm receipt of certain types of OSPF packets
used to establish and maintain adjacency with other OSPF routers
used to request more information about any entry in the BDR
used to announce new OSPF information and to reply to certain types of requests

5. Two routers need to be configured within a single OSPF area. Which two components need to be configured on both routers to achieve this? (Choose two.)

the same process ID
the same area ID
network addresses and wildcard masks
the same router ID
the same loop back address

6. Which routing protocol maintains a topology table separate from the routing table?

IGRP
RIPv1
RIPv2
EIGRP

7. A router has learned two equal cost paths to a remote network via the EIGRP and RIP protocols. Both protocols are using their default configurations. Which path to the remote network will be installed in the routing table?

the path learned via EIGRP
the path learned via RIP
the path with the highest metric value
both paths with load balancing

8. Refer to the exhibit. Host A is unable to access the Internet. What is the reason for this?

The IP address of host A is incorrect.
The default gateway of host A is incorrect.
The Fa0/1 interfaces of the two routers are configured for different subnets.
The subnet mask for the Fa0/0 interface of R1 is incorrect.

9. Which two locations can be the source of the Cisco IOS that is used by a router during the bootup process? (Choose two.)

flash memory
RAM
NVRAM
TFTP server
configuration register

10. Refer to the exhibit. R1 is configured properly for a single area OSPF, and R2 has been recently installed in the network. Which set of commands is required to configure a single area OSPF for the networks that are connected to R2?

R2(config)# router ospf 1
R2(config-router)# network 192.168.2.0 0.0.0.255 area 0
R2(config-router)# network 10.1.1.0 0.0.0.3 area 0
R2(config)# router ospf 1
R2(config-router)# network 192.168.2.0 0.0.0.255 area 0
R2(config)# router ospf 2
R2(config-router)# network 10.1.1.0 0.0.0.3 area 0
R2(config)# router ospf 1
R2(config-router)# network 192.168.2.0 0.0.0.255 area 0
R2(config-router)# network 10.1.1.0 0.0.0.3 area 1
R2(config)# router ospf 1
R2(config-router)# network 192.168.2.0 0.0.0.255 area 0
R2(config-router)# network 10.0.0.0 0.0.0.3 area 1

11. Refer to the exhibit. Routers R1 and R2 are directly connected via their serial interfaces and are both running the EIGRP routing protocol. R1 and R2 can ping the directly connected serial interface of their neighbor, but they cannot form an EIGRP neighbor adjacency.
What action should be taken to solve this problem?

Enable the serial interfaces of both routers.
Configure EIGRP to send periodic updates.
Configure the same hello interval between the routers.
Configure both routers with the same EIGRP process ID.

12. Refer to the exhibit. The interfaces of all routers are configured for OSPF area 0. R3 can ping R1, but the two routers are unable to establish a neighbor adjacency. What should the network administrator do to troubleshoot this problem?

Check if the interfaces of the routers are enabled.
Check the hello and dead intervals between the routers.
Check the process ID of both routers.
Check if CDP is enabled on all the routers.

13. Refer to the exhibit. The hosts that are connected to R2 are unable to ping the hosts that are connected to R1. How can this problem be resolved?

Configure the router ID on both routers.
Configure the R2 router interfaces for area 0.
Configure a loopback interface on both routers.
Configure the proper subnet masks on the router interfaces.

14. Refer to the exhibit. The command ip route 0.0.0.0 0.0.0.0 S0/0/0 is run on router R2. What are the two results of this command? (Choose two.)

A static route will be updated in the routing table.
The traffic from the Internet will be directed to R2.
The traffic from the source network 172.16.0.0/22 will be blocked.
The route will be specified as the default route for all networks not defined in the routing table.
All the broadcasts will be forwarded via the S0/0/0 interface of R2.

15. Refer to the exhibit. All routers are properly configured with default configurations and are running the OSPF routing protocol. The network is fully converged. A host on the 192.168.3.0/24 network is communicating with a host on the 192.168.2.0/24 network.
Which path will be used to transmit the data?

The data will be transmitted via R3-R2.
The data will be transmitted via R3-R1-R2.
The traffic will be load-balanced between two paths — one via R3-R2, and the other via R3-R1-R2.
The data will be transmitted via R3-R2, and the other path via R3-R1-R2 will be retained as the backup path.

16. In a lab test environment, a router has learned about network 172.16.1.0 through four different dynamic routing processes. Which route will be used to reach this network?

D 172.16.1.0/24 [90/2195456] via 192.168.200.1, 00:00:09, Serial0/0/0
O 172.16.1.0/24 [110/1012] via 192.168.200.1, 00:00:22, Serial0/0/0
R 172.16.1.0/24 [120/1] via 192.168.200.1, 00:00:17, Serial0/0/0
I 172.16.1.0/24 [100/1192] via 192.168.200.1, 00:00:09, Serial0/0/0

17. Which two technologies can be used in distance vector routing protocols to prevent routing loops? (Choose two.)

authentication
link-state advertisements
hold-down timers
Spanning Tree Protocol
split horizon

18. Refer to the exhibit. A network administrator wants to reduce the size of the routing table of R1. Which partial routing table entry in R1 represents the route summary for R2, without including any additional subnets?

10.0.0.0/16 is subnetted, 1 subnets
D 10.5.0.0[90/205891] via 192.168.1.2, S0/0/0
10.0.0.0/24 is subnetted, 4 subnets
D 10.5.0.0[90/205198] via 192.168.1.2, S0/0/0
10.0.0.0/22 is subnetted, 1 subnets
D 10.5.0.0[90/205901] via 192.168.1.2, S0/0/0
10.0.0.0/8 is subnetted, 4 subnets
D 10.5.0.0[90/205001] via 192.168.1.2, S0/0/0

19. Refer to the exhibit. How many routes are ultimate routes?

3
4
5
7

20. Which statement correctly describes a feature of RIP?

RIP is a link-state routing protocol.
RIP uses only one metric—hop count— for path selection.
Advertised routes with hop counts greater than 10 are unreachable.
Messages are broadcast every 10 seconds.

21. Refer to the exhibit. Which combination of IP address and subnet mask can be used on the serial interface of Router2 in order to put the interface in the same network as the serial interface of Router1?

IP 172.16.0.18, subnet mask 255.255.255.0
IP 172.16.32.15, subnet mask 255.255.255.240
IP 172.16.0.18, subnet mask 255.255.255.252
IP 172.16.32.18, subnet mask 255.255.255.252

22. The command ip route 192.168.2.0 255.255.255.0 172.16.2.2 was entered into the router. After network changes were made, the new next hop for the 192.168.2.0/24 network is 172.16.5.1. What should an administrator do so that the router will use the new next hop to reach the 192.168.2.0 network?

Enter the command clear ip route *.
Lower the administrative distance for the new path to ensure that it is used first.
Negate the original command and enter a new static route with the new next hop.
Nothing. The router will learn of the new next hop and automatically update the route table.

23. A network administrator is in charge of two separate networks that share a single building. What device will be required to connect the two networks and add a common connection to the Internet that can be shared?

hub
router
access point
Ethernet switch

24. A network administrator must use the subnet 172.16.128.0/18 to create 6 additional subnets each containing up to 2000 hosts for local LANs. Which subnet mask should the administrator use to create the new subnets?

255.255.224.0
255.255.240.0
255.255.248.0
255.255.252.0

25. When connecting two devices, which situation would normally require the use of a crossover cable?

connecting a host to a switch
connecting a switch to a router
connecting a switch to a switch
connecting a host to a router console port

26. Which router mode is accessed by entering the enable command?

user EXEC
privileged EXEC
global configuration
interface configuration

27. Refer to the exhibit. Based on the partial output in the exhibit, why can users establish a console connection to this router without entering a password?

The login command was not entered on the console line.
The enable password should be an enable secret password.
No username and password combination has been configured.
Console connections cannot be configured to require users to provide passwords.

28. Refer to the exhibit. Which option will provide the configuration that is needed for router R1 to dynamically learn routes to the 192.168.100.16/28, 192.168.100.32/28, and 192.168.100.48/28 subnetworks?

with static routes
with a routed protocol
with a routing protocol
with directly connected routes

29. Refer to the exhibit. The network is configured for RIPv2 routing. What path will a packet from router A take to reach the LAN that is attached to router F if the 56 kb/s link between router A and router E fails?

A, B, C, F
A, B, C, E, F
A, D, G, H, F
A, D, G, E, F
A, D, G, E, H, F

30. Refer to the exhibit. Routers R1 and R2 are directly connected through a FastEthernet link but cannot form a neighbor adjacency. What could resolve the problem?

The cost on R1 should be set higher.
The priority on R1 should be set higher.
The OSPF process ID numbers must match.
A backup designated router needs to be added to the network.
The hello and dead timers must be configured with the same values on both routers.

31. Which feature of RIPv2 enables it to function as a classless routing protocol?

Subnet masks are included in routing updates.
Routing updates are triggered by topology changes.
Next-hop addresses are included in routing updates.
Multicast addresses are used to send routing updates.

32. Refer to the exhibit. Which solution provides the most efficient use of router resources for forwarding traffic between BR and HQ?

RIP
RIPv2
EIGRP
static routes

33. Refer to the exhibit. A network administrator configures a static route on router R1 to reach the 192.168.1.0/24 network. Which IP address should be used as the next-hop address in the ip route command?

192.168.1.1
192.168.2.1
192.135.250.1
192.135.250.2

34. Refer to the exhibit. Which two interface variables will determine the metric that is used on EIGRP routes? (Choose two.)

load
delay
reliability
hop count
bandwidth

35. Which protocol is used by EIGRP to deliver and receive update packets?

FTP
RTP
TCP
TFTP
UDP

36. Which multicast address does EIGRP use to send hello and updates packets?

224.0.0.5
224.0.0.6
224.0.0.9
224.0.0.10

37. What is the key responsibility of the switching function within a router?

to choose the best path based on the lowest path cost
to encapsulate packets in the correct data link frame type
to look up the correct exit interface for the destination IP address
to look up the correct exit interface for the destination MAC address
to resolve the destination IP address into a destination MAC address

38. Refer to the exhibit. If the attached device is configured correctly, what action can be taken to change the state of FastEthernet0/0 to Up Up?

Attach a crossover cable to the interface.
Change the encapsulation on the interface to HDLC.
Issue the no shutdown command for the interface.
Set the clock rate for the interface to 56000.

39. Which two commands can be used to modify the default OSPF metric calculation of a link? (Choose two.)

R1(config-if)# bandwidth
R1(config-if)# ip ospf cost
R1(config-if)# ip ospf priority
R1(config-if)# ip ospf hello-interval
R1(config-router)# default-information originate

40. Refer to the exhibit. Which two statements are true based on the exhibited output? (Choose two.)

Automatic summarization is disabled.
The EIGRP routing protocol is being used.
There is one feasible successor in the routing table.
The serial interface S0/0/0 is administratively down.
The router created the route to 172.16.1.0/24 via the S0/0/0 interface.

41. Refer to the exhibit. Two connected routers are unable to establish adjacency. Based on the show ip ospf interface output, what could be the problem?

The dead timers do not match.
The routers have not reached full state.
The two routers are in different autonomous systems.
The physical interface between the two routers is down.

42. What is a characteristic of classful routing?

support for VLSM
the use of 48-bit addresses
routing updates do not include a subnet mask
addresses that are typically entered in hexadecimal format

43. Refer to the exhibit. A network administrator is investigating why data packets with destination addresses of 172.16.10.10 and 192.168.10.100 are being dropped instead of being forwarded via the static route as expected. After confirming that the ip classless command has been applied on all routers in the network, what other action should the administrator take to ensure that data packets to these addresses are forwarded via the static route?

Check that all routers are configured with the same autonomous system number.
Issue the no auto-summary command within the EIGRP configuration of all routers.
Issue the no passive-interface command within the EIGRP configuration of all routers.
Configure the static route to point to the next hop address instead of the outbound interface.

44. A router in an EIGRP enterprise network has a default route configured via the interface that connects to the ISP. Which command would the network administrator apply on this router so that other routers in the EIGRP AS 100 network will use this default route?

redistribute static
redistribute eigrp 100
redistribute connected
default-information originate

45. A network administrator configures a new router and saves the configuration. The router is taken to the installation site and installed. On startup, what component will the router search first by default for the saved configuration?

CompactFlash
CPU
boot ROM
flash
NVRAM
UART

46. Refer to the exhibit. A network engineer removes a new router from the shipping container and powers on the router to ensure it passes POST. Which port would the engineer use to perform the initial configuration?

AUX
console
FE0/0
FE0/1

47. Refer to the exhibit. A ping between host A and host B is successful, but pings from host A to operational hosts on the Internet fail. What is the reason for this problem?

The FastEthernet interface of R1 is disabled.
One of the default routes is configured incorrectly.
A routing protocol is not configured on both routers.
The default gateway has not been configured on host A.

48. You have been asked to explain converged networks to a trainee. How would you accurately describe a converged network?

A network is converged when all routers have formed an adjacency.
A network is converged immediately after a topology change has occurred.
A network is converged when all routers flush the unreachable networks from their routing tables.
A network is converged after all routers share the same information, calculate best paths, and update their routing tables.

49. A network administrator is troubleshooting a RIPv2 network that is not converging as expected. Which command can the administrator use on each router to view the RIPv2 updates as they are received?

debug ip rip
show ip route
debug ip routing
show ip protocols
show ip interface brief

50. A network administrator is setting up a new router with a device name of Admin, an encrypted password of cangetin, and the IP address 192.168.1.22/29 assigned to the first FastEthernet interface. Which command sequence correctly configures this router?

Router(config)# hostname Admin
Admin(config)# enable secret cangetin
Admin(config)# interface fa0/1
Admin(config-if)#ip address 192.168.1.22 255.255.255.248
Router(config)# hostname Admin
Admin(config)# enable password cangetin
Admin(config)# interface fa0/1
Admin(config-if)# ip address 192.168.1.22 255.255.255.248
Router(config)# hostname Admin
Admin(config)# enable secret cangetin
Admin(config)# interface fa0/0
Admin(config-if)# ip address 192.168.1.22 255.255.255.248
Router(config)# hostname Admin
Admin(config)# enable password cangetin
Admin(config)# interface fa0/0
Admin(config-if)# ip address 192.168.1.22 255.255.255.248

Mai jos gasiti cateva poze:

Recently, I wanted to create a browser game and host it on my computer. So, I began searching for a website that could offer me a stable DNS and found no-ip.com. After registering an account, I created a free subdomain on their website.

The next step was to set my router to create a link between the subdomain and my computer. At first, I set the router’s DHCP to offer me a static IP every time from Home > DHCP > Static DHCP. Then I created a link between the Internet and the local network by accessing Advanced > Virtual Server and setting the following options:

Private IP: 192.168.0.23 (the static IP that the router gives me)
Protocol type: TCP
Private port: 8088 (the port used by WAMP Server)
Public port: 80 (the port on which the subdomain runs; it’s usually 80)

After that, I made the connection with no-ip.com from Advanced > DDNS, so the router would change the DNS each time I turn on my computer.

Finally, I made the connection between WAMP Server and no-ip.com. I accessed WAMP Server > Apache > httpd.conf and modified the following lines:

Listen: 8088 (the port used by WAMP Server, it’s modification is optional)
ServerName: subdomain.no-ip.info

We restart the router, WAMP Server and our server is ready to use.

2. Which of the following are primary functions of a router? (Choose two.)
packet switching
microsegmentation
domain name resolution
path selection
flow control

3. Refer to the routing table shown in the exhibit. What is the meaning of the highlighted value 192?
It is the value assigned by the Dijkstra algorithm that designates the number of hops in the network.
It is the value used by the DUAL algorithm to determine the bandwidth for the link.
It is the metric, which is cost.
It is the administrative distance.

4. Which three statements are true regarding the encapsulation and de-encapsulation of packets when traveling through
a router? (Choose three.)
The router modifies the TTL field, decrementing it by one.
The router changes the source IP to the IP of the exit interface.
The router maintains the same source and destination IP.
The router changes the source physical address to the physical address of the exit interface.
The router changes the destination IP to the IP of the exit interface.
The router sends the packet out all other interfaces, besides the one it entered the router on.

Refer to the exhibit. Which path will traffic from the 172.16.1.0/24 network take to get to the 10.0.0.0/24 network?
ADC
ABC
It will load balance the traffic between ADC and ABC
It will send the traffic via ABC, and will use ADC as a backup path only when ABC fails.

5. What is the purpose of the TTL field within an IP packet header?
clears an unreachable route from the routing table after the invalid timer expires
prevents regular update messages from inappropriately reinstating a route that may have gone bad
removes an unreachable route from the routing table after the flush timer expires
limits the period of time or number of hops a packet can traverse through the network before it should be discarded
used to mark the route as unreachable in a routing update that is sent to other routers

6. Refer to the exhibit. How many routes are both level 1 and qualify for use as an ultimate route?
1
2
3
4
5
6

7. Refer to the exhibit. Cost for each path are shown. If all routers are configured to use OSPF, what would be the path of a packet sent from Router C to Router D if Router A was down?
C-B-E-D
C-B-A-D
C-F-E-D
C-F-B-A-D
C-F-E-A-D

8. Refer to the exhibit. Routers 1 and 2 are directly connected over a serial link. Pings are failing between the two routers. What change by the administrator will correct the problem?
Set the encapsulation on both routers to PPP.
Decrease the bandwidth on Serial 0/1/0 on router 2 to 1544.
Change the cable that connects the routers to a crossover cable.
Change the IP address on Serial 0/1/0 on router 2 to 192.168.0.1/30.

9. Refer to the exhibit. A network administrator is trying to determine why router JAX has no OSPF routes in its routing table. All routers are configured for OSPF area 0. From the JAX router, the administrator is able to ping its connected interfaces and the Fa0/1 interface of the ORL router but no other router interfaces. What is a logical step that the network administrator should take to troubleshoot the problem?
Reboot the routers.
Change the OSPF process ID on all of the routers to 0.
Check to see if the cable is loose between ORL and JAX.
Check to see if CDP packets are passing between the routers.
Use show and debug commands to determine if hellos are propagating

10. Refer to the exhibit. Which summarization should R1 use to advertise its networks to R2?
192.168.1.0/24
192.168.0.0/24
192.168.0.0/22
192.168.1.0/22

11. A router boots and enters setup mode. What is the reason for this?
The IOS image is corrupt.
Cisco IOS is missing from flash memory.
The configuration file is missing from NVRAM.
The POST process has detected hardware failure.

12. Refer to the exhibit. R1 is configured properly for a single area OSPF, and R2 has been recently installed in the network. Which set of commands is required to configure a single area OSPF for the networks that are connected to R2?
R2(config)# router ospf 1
R2(config-router)# network 192.168.2.0 0.0.0.255 area 0
R2(config-router)# network 10.1.1.0 0.0.0.3 area 0
R2(config)# router ospf 1 R2(config-router)# network 192.168.2.0 0.0.0.255 area 0 R2(config)# router ospf 2 R2(config-router)# network 10.1.1.0 0.0.0.3 area 0
R2(config)# router ospf 1 R2(config-router)# network 192.168.2.0 0.0.0.255 area 0 R2(config-router)# network 10.1.1.0 0.0.0.3 area 1
R2(config)# router ospf 1 R2(config-router)# network 192.168.2.0 0.0.0.255 area 0 R2(config-router)# network 10.0.0.0 0.0.0.3 area 1

13. Refer to the exhibit. Routers R1 and R2 are directly connected via their serial interfaces and are both running the EIGRP routing protocol. R1 and R2 can ping the directly connected serial interface of their neighbor, but they cannot form an EIGRP neighbor adjacency.
What action should be taken to solve this problem?
Enable the serial interfaces of both routers.
Configure EIGRP to send periodic updates.
Configure the same hello interval between the routers.
Configure both routers with the same EIGRP process ID

14. Refer to the exhibit. The hosts that are connected to R2 are unable to ping the hosts that are connected to R1. How can this problem be resolved?
Configure the router ID on both routers.
Configure the R2 router interfaces for area 0.
Configure a loopback interface on both routers.
Configure the proper subnet masks on the router interfaces.

15. In a lab test environment, a router has learned about network 172.16.1.0 through four different dynamic routing processes. Which route will be used to reach this network?
D 172.16.1.0/24 [90/2195456] via 192.168.200.1, 00:00:09, Serial0/0/0
O 172.16.1.0/24 [110/1012] via 192.168.200.1, 00:00:22, Serial0/0/0
R 172.16.1.0/24 [120/1] via 192.168.200.1, 00:00:17, Serial0/0/0
I 172.16.1.0/24 [100/1192] via 192.168.200.1, 00:00:09, Serial0/0/0

16. Which statement is true about the metrics used by routing protocols?
A metric is a value used by a particular routing protocol to compare paths to remote networks.
A common metric is used by all routing protocols.
The metric with the highest value is installed in the routing table.
The router may use only one parameter at a time to calculate the metric

17. Refer to the exhibit. Both routers are using the RIPv2 routing protocol and static routes are undefined. R1 can ping
192.168.2.1 and 10.1.1.2, but is unable to ping 192.168.4.1.
What is the reason for the ping failure?
The serial interface between two routers is down.
R2 is not forwarding the routing updates.
The 192.168.4.0 network is not included in the RIP configuration of R2.
RIPv1 needs to be configured.

18. Which two statements are true about the EIGRP successor route? (Choose two.)
It is saved in the topology table for use if the primary route fails.
It may be backed up by a feasible successor route.
It is used by EIGRP to forward traffic to the destination.
It is flagged as active in the routing table.
After the discovery process has occurred, the successor route is stored in the neighbor table

19. Refer to the exhibit. Hosts on the 192.168.1.0 network cannot communicate with hosts on the 172.16.1.1 network. The network administrator has run the show ip route command on R1. What could be the cause of this problem?
The FastEthernet interface on R1 is disabled.
Autosummarization is enabled on R1.
The serial interface S0/0/0 of R1 is administratively down.
No static route or routing protocol is configured.

20. Which statement correctly describes a feature of RIP?
RIP is a link-state routing protocol.
RIP uses only one metric—hop count— for path selection.
Advertised routes with hop counts greater than 10 are unreachable.
Messages are broadcast every 10 seconds

21. Refer to the exhibit. Which two statements are true based on the exhibited output? (Choose two.)
All routes are stable.
Each route has one feasible successor.
The serial interface between the two routers is down.
The administrative distance of EIGRP has been set to 50.
The show ip eigrp topology command has been run on R1.

22. A network administrator is analyzing routing update behavior on a network that has both EIGRP and OSPF
configured on all routers. Both protocols appear in the output of show ip protocols. However, only EIGRP internal
routes appear in the routing tables. Which statement correctly explains the scenario?
The OSPF protocol has a higher cost than EIGRP.
The EIGRP protocol has a lower metric than OSPF.
The EIGRP protocol was configured first on the router.
The EIGRP protocol has a lower administrative distance than OSPF

23. Which prompt is used to allow a user to change the IP address of an interface on a router?
Router>
Router#
Router(config)#
Router(config-if)#

24. Refer to the exhibit. Routers RTRA and RTRB are running OSPF. What entry does RTRA add in the routing table
when Serial 0/0/0 receives an update about the network that is attached to RTRB?
O 172.16.7.0/30 [110/51] via 10.10.10.2, 00:00:25, Serial0/0/0
O 172.16.7.16/28 [110/51] via 10.10.10.2, 00:00:25, Serial0/0/0
O 172.16.7.0/24 [110/51] via 10.10.10.2, 00:00:25, Serial0/0/0
O 172.16.0.0/16 [110/51] via 10.10.10.2, 00:00:25, Serial0/0/0

25. Which additional piece of information is included in the updates of classless routing protocols to support the use of VLSM and discontiguous networks?
metric
network mask
neighbor router ID
administrative distance

26. Because of a topology change, the next hop IP address in the current static route must be reconfigured. How can a static route entry be altered to accommodate a topology change?
Keep the existing static route and configure a new static route with the correct next hop IP address.
Negate the existing static route and configure a new static route with the correct next hop IP address.
Do nothing. The existing static route will automatically update the next hop entry with the new IP address.
Keep the existing static route, reload the router, and configure a new static route with the correct next hop IP address

27. Which router mode is accessed by entering the enable command?
user EXEC
privileged EXEC
global configuration
interface configuration

28. Refer to the exhibit. An administrator is attempting to configure a router by copying and pasting the commands that are shown in the exhibit. However, only one of the FastEthernet interfaces is coming up. What is the problem?
Both interfaces are in the same IP subnet.
FastEthernet0/1 does not have a description.
There can be only one FastEthernet interface enabled on a router at one time.
The administrator did not exit to global configuration mode before configuring FastEthernet0/1

29. In an examination of two OSPF routers that fail to exchange information, it is determined that they have not become OSPF neighbors. Which two configuration values must match for the OSPF routers to become neighbors?
neighbor ID and router ID
dead time and hello time
OSPF area and neighbor ID
OSPF area and interface priority

30. Refer to the exhibit. Routers R1 and R3 use different routing protocols with default administrative distance values. All devices are properly configured and the destination network is advertised by both protocols. Which path will be used to transmit the data packets from PC1 to PC2?
The packets will travel via R2-R1.
The packets will travel via R2-R3.
The traffic will be load-balanced between two paths — via R2-R1 and via R2-R3.
The packets will travel via R2-R3, and the other path via R2-R1 will be retained as the backup path

31. Refer to the exhibit. The network administrator has run the following command on R1. R1(config)# ip route 192.168.2.0 255.255.255.0 172.16.1.2 What is the result of running this command?
Traffic for network 192.168.2.0 is forwarded to 172.16.1.2.
This route is automatically propagated throughout the entire network.
Traffic for all networks is forwarded to 172.16.1.2.
The command invokes a dynamic routing protocol for 192.168.2.0

32. Why is fast convergence desirable in networks that use dynamic routing protocols?
Hosts are unable to access their gateway until the network is converged.
Routers will not allow packets to be forwarded until the network is converged.
Routers may make incorrect forwarding decisions until the network has converged.
Routers will not allow configuration changes to be made until the network has converged

33. Which two statements about routing protocols are accurate? (Choose two.)
OSPF supports VLSM.
RIPv1 supports VLSM.
RIPv2 does not have a hop count limit.
EIGRP supports discontiguous network designs.
RIPv2 does not support discontiguous network designs

34. Refer to the exhibit. If the EIGRP routing protocol is used throughout the network, which IP address and mask prefix
should be sent by router R1 to the Edge router as a result of manual summarization of LANs A, B, C, and D?
192.168.4.0/20
192.168.4.0/22
192.168.4.0/24
192.168.4.0/26

35. Refer to the exhibit. Which solution provides the most efficient use of router resources for forwarding traffic between BR and HQ?
RIP
RIPv2
EIGRP
static routes

36. Refer to the exhibit. The network is configured with RIPv2. However, network administrators notice that communication cannot be successfully completed from one LAN to another. A network administrator issues the show ip route command on the HQ router. Based on the output, what should be done to correct the problem?
Disable the load balancing feature of RIPv2.
Issue the no auto-summary command for RIPv2.
Replace RIPv2 with EIGRP which supports VLSM.
Make sure that the network statements include the correct subnet mask

37. Which protocol is used by EIGRP to deliver and receive update packets?
FTP
RTP
TCP
TFTP
UDP

38. Which multicast address does EIGRP use to send hello and updates packets?
224.0.0.5
224.0.0.6
224.0.0.9
224.0.0.10

39. A network administrator is using an application that is monitoring packets on the network and sees an EIGRP update packet. What is the purpose of the update packet?
The packet is sent to discover neighbors within the EIGRP network.
The packet is sent to search for network devices within an EIGRP network.
The packet is used to propagate routing information within the EIGRP network.
The packet is used to send an unreachable reply to another router within the EIGRP network.
The packet is used to notify all routers that EIRGP has failed on one of the routers within the EIGRP network

40. Refer to the exhibit. What OSPF network statements are required for the router B to advertise the three networks that are attached?
router ospf 1 network 10.0.0.0 0.0.0.255 area 0
router ospf 1 network 10.1.1.0 0.3.255.255 area 0 network 10.10.1.0 0.255.255.255 area 0 network 10.20.1.0 0.255.255.255 area 0
router ospf 1 network 10.1.1.0 0.0.0.3 area 0 network 10.10.1.0 0.0.255.255 area 0 network 10.20.1.0 0.0.255.255 area 0
router ospf 1 network 10.1.1.0 0.0.0.3 area 0 network 10.10.1.0 0.0.0.255 area 0 network 10.20.1.0 0.0.0.255 area 0

41. Refer to the exhibit. Why is the state of the serial0/0/0 interface administratively down?
An IP address has not been configured on the interface.
The WIC was installed into the incorrect slot on the router.
The default encapsulation on the interface has been modified.
The no shutdown command has not been executed on the interface

42. On a router, which three components are stored in RAM? (Choose three.)
POST code
the routing table
the running-configuration
the start-up configuration
the bootstrap instructions
a copy of the operating system

43. Refer to the exhibit. RouterA and RouterB cannot successfully exchange EIGRP routes. What is the problem?
The hello intervals do not match.
The autonomous system numbers do not match.
The no auto-summary command is missing from both routers.
The ip bandwidth-percent command is missing from RouterB

44. Refer to the exhibit. What is the purpose of the ip bandwidth-percent eigrp 50 10 command?
to limit the bandwidth EIGRP packets can use to 6.4 kb/s
to limit the bandwidth EIGRP packets can use to 10 kb/s
to limit the bandwidth EIGRP packets can use to 32 kb/s
to limit the bandwidth EIGRP packets can use to 50 kb/s

45. A network administrator adds the default-information originate command to the configuration of a router that uses RIP as the routing protocol. What will result from adding this command?
The router will be reset to the default factory information.
The router will not forward routing information that is learned from other routers.
The router will propagate a static default route in its RIP updates, if one is present.
The router will only forward packets that originate on directly connected networks

46. A network technician is configuring a Cisco 2811 router. The technician types conf at the privileged level command prompt and presses the TAB key. What action will the router take?
It will revert to the user mode.
It will perform an auto-complete function.
It will go into the global configuration mode.
It will give an error message that indicates a bad command was entered

47. What is a function of the console port on a router?
It is used to manage the router.
It is used for packet receiving and forwarding.
It is used to interconnect various types of LANs.
It is used to interconnect a variety of serial links including T1, DSL, and ISDN

48. Refer to the exhibit. Which route will be installed in the routing table on R1 to forward traffic from PC1 to the web server?
the static route
the route learned via OSPF
the route learned via EIGRP
both routes learned via OSPF and EIGRP

49. Refer to the exhibit. After the commands are entered, which password will be required to establish a Telnet session
with the router?
cisco
letmein
please
access

Va pot spune de pe acum ca diferenta fata de un stick normal pe USB 2.0 este enorma. Problema la mine a fost ca am port USB 2.0 si nu de 3.0, insa asta nu l-a impiedicat sa-si arate toate calitatile. Am tot citit review-uri insa toate mi se par cam la fel. Un stick nu “se testeaza” cu HDTune sau mai stiu eu ce program ci efectuand diferite transferuri. Doar asa poti vedea cat suporta si cum se comporta cu adevarat.

Inca de la inceput, trebuie sa va spun ca pana in prezent am mai interactionat cu produse din gama Corsair, astfel incat sa-mi fac o impresie despre produsele lor. Stick-ul pe care vi-l voi prezenta astazi are un design original, construit din aluminiu de 1mm si pe margine avand cauciuc, impiedicand apa sa intre. Cei de la Corsair au reusit sa construiasca un stick rezistent la evenimentele de zi cu zi (scapat din mana sau bagat in apa, dat dupa oameni pe strada, spart geamuri …  )
Mai jos va voi arata cum s-a comportat stick-ul Corsair Survivor USB 3.0 in diferitele situatii.

In tot acest timp cat am copiat fisiere pe el si de pe el, laptopul a rulat diferite aplicatii (Messenger, Skype, TeamViewer, Outlook, Chrome, Filezilla si Winamp).
Cat timp am copiat fisierele, stick-ul nu s-a incalzit deloc.

Ca si performante pe un port USB2.0, stick-ul Corsair Survivor 16GB se descurca foarte bine avand in vedere ca are suport de conectare pe USB3.0. La transfer de fisiere viteza maxima a fost undeva la 28 MB/s (in poze nu apare). In a 2 poza, nu stiu cum de a aratat 55 MB, conectarea fiind pe USB2.0 si ramanand intre 50-55 MB pana la copierea intregului fisier. Limia maxima, din cate stiu pe USB 2.0 este de ~30 MB/s.

Avantaje

[+] Viteză de scriere/citire și transfer fișiere foarte mare cu ajutorul portului USB 3.0
[+] Nu se incalzeste deloc
[+] Design ok, material placut la atingere
[+] Pret cuprins intre 110 si 170 lei

Dezavantaje

[-] Dimensiune mare, lungime 86mm si grosime 25mm

Ediţia de anul acesta a conferinţei se va desfăşura la Grand Hotel Napoca în perioada 6-8 septembrie 2012.